Strongflex 086231A – rear suspension bush kit SPORT Honda Accord VII Tourer 03–08

Strongflex 086231A – rear suspension kit SPORT polyurethane Honda Accord VII Tourer 03–08

The Strongflex 086231A rear suspension kit is a complete set of polyurethane bushes dedicated to the Honda Accord VII Tourer (CM, 2003–2008). With a hardness of 90 ShA, this kit is aimed at drivers who expect a much more precise and predictable chassis – whether for fast road use, spirited driving on twisty roads or occasional track days. Stiffer polyurethane reduces unwanted arm deflection, keeps the suspension geometry stable under load and improves steering feedback compared to worn rubber bushes.

In contrast to comfort-oriented rubber solutions, this rear suspension kit focuses on performance, control and stability. Properly fitted, it noticeably tightens up the rear axle response, reduces play during hard cornering and braking, and helps the Accord Tourer feel more confident with sportier springs, dampers or wider tyres.

Vehicle compatibility – Strongflex 086231A

Fits:

• Honda Accord VII (2002–2008) Tourer CM – all engine versions

The kit is designed as a direct replacement for the factory rubber bushes on the rear suspension of the Accord VII Tourer. No welding or modification of the suspension arms is required – old bushes are pressed out, new polyurethane elements are pressed in.

Kit contents – rear suspension bush kit 086231A

The kit includes the following polyurethane components:

• 2 × 081831A – rear trailing arm bush (performance grade)
• 2 × 081832A – rear upper arm bush (performance grade)
• 4 × 081833A – rear arm bush (performance grade)
• 2 × 081834A – rear transverse arm bush (performance grade)
• 2 × 081835A – rear knuckle bush (performance grade)
• 2 × 081533A – front / rear anti-roll bar bush (performance grade)

Total number of bushes in the kit: 14
Number of kits required per car: 1

Material, hardness and driving characteristics

• Material: polyurethane (PUR/PU)
• Hardness: 90 ShA – performance-oriented compound

Polyurethane with 90 ShA hardness provides a noticeable increase in stiffness over OEM rubber while remaining resistant to ageing, oil and road salt. On the road this translates into:

• more direct rear axle response and better feedback at higher speeds,
• improved stability when changing lanes and during fast cornering,
• more consistent wheel alignment under braking and acceleration,
• reduced “floating” feeling typical for tired factory bushes.

Due to its sporty character, the kit can transmit slightly more vibration and noise into the cabin compared to soft rubber bushes. For drivers who prioritise comfort over precision, a road-biased rear suspension kit with a lower-hardness compound may be a better choice. For tuned or more dynamically driven Accord Tourer, the 086231A set gives a much more confident and stable rear end.

Installation notes and maintenance

Each Strongflex kit is supplied with dedicated mounting grease, which should be used during installation to ensure proper operation and prevent squeaking. For best results:

• clean all bores and sleeves in the arms thoroughly before pressing the new bushes in,
• use suitable tools or a press to avoid damaging the polyurethane or metal inserts,
• tighten all suspension bolts with the car on its wheels (under load) to avoid pre-loading the bushes in an unnatural position,
• after installation, perform a full wheel alignment of the car.

The polyurethane material is highly resistant to deformation, so the kit is designed to operate reliably for a long time, even under increased loads and in demanding conditions (lowering, grippier tyres, dynamic driving).

FAQ – rear suspension kit Strongflex 086231A for Honda Accord VII Tourer

Does this kit fit the sedan or coupe versions of the Accord VII?
No, the 086231A kit is designed exclusively for the Honda Accord VII Tourer (CM, 2003–2008). For sedan or coupe models, a different rear suspension kit must be used.

Is this kit suitable for everyday use?
The 90 ShA compound is primarily targeted at drivers who value sharp handling and a performance-oriented feel. The car will be stiffer and more precise, but some increase in NVH (noise, vibration, harshness) is possible compared with soft OEM rubber. For maximum comfort there are softer, more road-biased kits available.

Is additional maintenance required after installation?
Under normal road conditions, polyurethane bushes do not require special maintenance. It is recommended to periodically check the condition of the suspension, bolts and alignment, especially on cars used for more dynamic driving or with lowered suspension.

Each Strongflex rear suspension kit is supplied with installation grease – use it according to the instructions to ensure quiet and reliable operation of the bushes.